作者: golf988 时间: 2012-12-14 14:15
一套WEISS JASON 转盘 MEDIA解码 CASTOR单声道后级效果俱佳。JASON 转盘+MEDIA解码 可直驱CASTOR单声道后级，瑞士品质，勿容置疑. 作者: golf988 时间: 2012-12-14 14:32
The CASTOR power amplifier is based on class D technology and brings a new
level of performance in this category. Each mono block unit offers 600 watts
of power (at 4 Ohms) with an extremely low output impedance, low noise and
distortion and a 50kHz bandwidth. The input level can be set with a 12
position switch. Inputs are selectable between XLR (balanced) and RCA
(unbalanced). The two Castor units in a stereo system can be linked such that
power can be switched on/off on both units from within a single unit. The
power supply is analog with ample power capacity. Care has been taken to keep
the signal path as short as possible, avoiding any unnecessary active or
passive elements.
Technical Details:
Inputs: One XLR input (balanced) and one RCA input (unbalanced). The active
input is selected with a toggle switch.
Input Gain: Set with a 12 position rotary switch between 0 and -22dB in 2dB
steps.
Outputs: Two pairs of WBT connectors suited for bi-wiring speakers. The
connectors are fully isolated for safety reasons.
Power Supply: A powerful non-switching power supply is used. Storage
capacitors are audiophile slit-foil types. The mains voltage can be set to
100..120V or 200..240V. Standby power is a mere 2 Watts. Because of the class
D design the wasted power is extremely low. Depending on the output power
level, an efficiency of more than 90% is achieved.
Mechanical Design: The CASTOR employs a twin metal frame. The inner chassis is
made of steel for effective shielding against electrostatic and
electromagnetic radiation. The outer frame is individually made to our
exacting standards from massive anodized aluminium for additional shielding,
heat convection - and of course stunning looks.
Frontpanel controls: One power switch with corresponding LED.
Backpanel elements: Analog inputs on XLR and RCA connectors with input level
range switch. Analog outputs on two pairs of WBT connectors. Power link
connector, allowing for connecting two amplifiers for simultaneous on/off
switching from within a single unit. Input selection switch. Input gain
switch. Mains connector with fuses and voltage selector.
Technical Data:
昑otal Harmonic Distortion up to 400W: <0.02%
昑otal Harmonic Distortion up to 600W: <0.1%
昑otal Harmonic Distortion is frequency independent
昈utput Noise: 125dB below full scale, unweighted
旻requency Response: 10Hz�50kHz +0/-3dB load independent
昈utput Impedance: 20mOhm at f <= 1kHz
昈utput Power: 600Watt at 4 Ohm / 300Watt at 8 Ohm
The CASTOR power amplifier is based on class D technology and brings a new
level of performance in this category. Each mono block unit offers 600 watts
of power (at 4 Ohms) with an extremely low output impedance, low noise and
distortion and a 50kHz bandwidth. The input level can be set with a 12
position switch. Inputs are selectable between XLR (balanced) and RCA
(unbalanced). The two Castor units in a stereo system can be linked such that
power can be switched on/off on both units from within a single unit. The
power supply is analog with ample power capacity. Care has been taken to keep
the signal path as short as possible, avoiding any unnecessary active or
passive elements.
Technical Details:
Inputs: One XLR input (balanced) and one RCA input (unbalanced). The active
input is selected with a toggle switch.
Input Gain: Set with a 12 position rotary switch between 0 and -22dB in 2dB
steps.
Outputs: Two pairs of WBT connectors suited for bi-wiring speakers. The
connectors are fully isolated for safety reasons.
Power Supply: A powerful non-switching power supply is used. Storage
capacitors are audiophile slit-foil types. The mains voltage can be set to
100..120V or 200..240V. Standby power is a mere 2 Watts. Because of the class
D design the wasted power is extremely low. Depending on the output power
level, an efficiency of more than 90% is achieved.
Mechanical Design: The CASTOR employs a twin metal frame. The inner chassis is
made of steel for effective shielding against electrostatic and
electromagnetic radiation. The outer frame is individually made to our
exacting standards from massive anodized aluminium for additional shielding,
heat convection - and of course stunning looks.
Frontpanel controls: One power switch with corresponding LED.
Backpanel elements: Analog inputs on XLR and RCA connectors with input level
range switch. Analog outputs on two pairs of WBT connectors. Power link
connector, allowing for connecting two amplifiers for simultaneous on/off
switching from within a single unit. Input selection switch. Input gain
switch. Mains connector with fuses and voltage selector.
Technical Data:
total Harmonic Distortion up to 400W: <0.02%
total Harmonic Distortion up to 600W: <0.1%
total Harmonic Distortion is frequency independent
output Noise: 125dB below full scale, unweighted
frequency Response: 10Hz�50kHz +0/-3dB load independent
output Impedance: 20mOhm at f <= 1kHz
utput Power: 600Watt at 4 Ohm / 300Watt at 8 Ohm